GLX_INTEL_swap_event is broken on the server side, where it's
currently unconditionally enabled. This completely breaks
systems running on drivers which don't support that extension.
There's no way to test for its presence on this side, so instead
of disabling it uncondtionally, just disable it for drivers
which are known to not support it. It makes sense because
most drivers do support it right now.
We'll be able to remove this once Xserver properly advertises
GLX_INTEL_swap_event.
Note: This is a candidate for stable branch branches.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60052
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Brian Paul <brianp@vmware.com>
Tested-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit 076403c30d)
In GLSL, sampler indices are allocated contiguously from 0. But in the
case of ARB_fragment_program (and possibly fixed function), an app that
uses texture 0 and 2 will use sampler indices 0 and 2, so we were only
allocating space for samplers 0 and 1 and setting up sampler 0. We
would read garbage for sampler 2, resulting in flickering textures and
an angry simulator.
Fixes bad rendering in 0 A.D. and ETQW. This was fixed for pre-gen7 by
28f4be9eb9
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=25201
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58680
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
NOTE: This is a candidate for stable branches.
(cherry picked from commit 5bb05c6e6d)
Before, we'd spill one reg, then continue on without actually register
allocating, then assertion fail when we tried to use a vgrf number as a
register number.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit d4bcc65918)
This should have been picked when 9237f0e was picked.
Bugzill: https://bugs.freedesktop.org/show_bug.cgi?id=59700
Ivybridge doesn't appear to have the same errata as Sandybridge; no
corruption was observed by setting it to more than the minimal correct
value. It's possible that we were simply lucky, since the URB entries
are 1024-bit on Ivybridge vs. 512-bit Sandybridge. Or perhaps the
underlying hardware issue is fixed.
Either way, we may as well program the minimum value since it's now
readily available, likely to be more efficient, and possibly more
correct.
v2: Use GEN7_SBE_* defines rather than GEN6_SF_*. (A copy and paste
mistake.) They're the same, but using the right names is better.
Reviewed-by: Paul Berry <stereotype441@gmail.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 44aa2e15f6)
(This commit message was primarily written by Paul Berry, who explained
what's going on far better than I would have.)
Previous to this patch, we thought that the only restrictions on
3DSTATE_SF's URB read length were (a) it needs to be large enough to
read all the VUE data that the SF needs, and (b) it can't be so large
that it tries to read VUE data that doesn't exist. Since the VUE map
already tells us how much VUE data exists, we didn't bother worrying
about restriction (a); we just did the easy thing and programmed the
read length to satisfy restriction (b).
However, we didn't notice this erratum in the hardware docs: "[errata]
Corruption/Hang possible if length programmed larger than recommended".
Judging by the context surrounding this erratum, it's pretty clear that
it means "URB read length must be exactly the size necessary to read all
the VUE data that the SF needs, and no larger". Which means that we
can't program the read length based on restriction (b)--we have to
program it based on restriction (a).
The URB read size needs to precisely match the amount of data that the
SF consumes; it doesn't work to simply base it on the size of the VUE.
Thankfully, the PRM contains the precise formula the hardware expects.
Fixes random UI corruption in Steam's "Big Picture Mode", random terrain
corruption in PlaneShift, and Piglit's fbo-5-varyings test.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56920
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60172
Tested-by: Jordan Justen <jordan.l.justen@intel.com> (v1/Piglit)
Tested-by: Martin Steigerwald <martin@lichtvoll.de> (PlaneShift)
Reviewed-by: Paul Berry <stereotype441@gmail.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 09fbc29828)
The maximum SF source attribute is necessary to compute the Vertex URB
read length properly, which will be done in the next commit.
Reviewed-by: Paul Berry <stereotype441@gmail.com>
Tested-by: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 5e9bc7bd12)
The next patch will benefit from easy access to the source attribute
number and whether or not we're swizzling. It doesn't want the final
attr_override DWord form, however.
Reviewed-by: Paul Berry <stereotype441@gmail.com>
Tested-by: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit b3efc5bea8)
This optimized filter (when using repeat wrap modes,
linear min/mag/mip filters, pot textures) only applies to 2d textures,
but nothing prevented it from being used for other textures (likely
leading to very bogus sample results).
Note: This is a candidate for the 9.0 branch.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 66b6d51214)
We weren't emitting the SVGA_RS_OUTPUTGAMMA state so sRGB rendering
didn't work properly.
Fixes piglit's framebuffer-srgb test.
Note: This is a candidate for the stable branches.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit ff60509157)
glRasterPos doesn't exist in the core profile.
NOTE: This is a candidate for the stable branches (9.0 and 9.1).
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit cc5fdaf2dc)
Conflicts:
src/mesa/main/extensions.c
Note: This is a candidate for the 9.0 branch.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 8f3c81d018)
Conflicts:
src/mesa/main/extensions.c
Check the return value of calls to u_upload_alloc() and
u_upload_data() and return early if needed.
Since we don't have a way to propagate errors all the way up to
Mesa through pipe_context::draw_vbo(), call debug_warn_once() so
the user might have some clue about OOM errors.
Note: This is a candidate for the 9.0 branch.
(cherry picked from commit b13c534f14)
Conflicts:
src/gallium/auxiliary/util/u_vbuf.c
We weren't properly checking the return value of these calls (and
calls to u_upload_data()) to detect OOM errors.
Note: This is a candidate for the 9.0 branch.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 8c3f9ea073)
Some callers of this function were checking the 'ptr' result to see if
the function failed. But the correct way is to check the regular
return value for PIPE_ERROR_x. Now we initialize all the returned
values at the top of the function in case we do hit an error (like OOM).
Callers are more likely to detect OOM conditions now. But there
are some callers which don't do any error checking...
Note: This is a candidate for the 9.0 branch.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 68a097596e)
Conflicts:
src/gallium/auxiliary/util/u_upload_mgr.c
In my testing I haven't found any cases where we get a null context
pointer, but it might still be possible. Check for null just to be safe.
Note: This is a candidate for the stable branches.
(cherry picked from commit a4311054c7)
We were warning when there was no current context and we're about
to delete a renderbuffer, but that happens fairly often and isn't
really a problem.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=57754
Note: This is a candidate for the stable branches.
Tested-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit 006918c0db)
the critical error would use driverName.
Found by internal RH coverity scan.
Note: This is a candidate for stable branches.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit a0ec9185eb)
Conflicts:
src/glx/dri_glx.c
The use-after-free happened when the renderbuffer was shared by multiple
contexts and we tried to delete the renderbuffer using a context which
was previously deleted.
Note: this is a candidate for the stable branches.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 4cedb65a43)
We sometimes need a rendering context when deleting renderbuffers.
Pass it explicitly instead of trying to grab a current context
(which might be NULL). The next patch will make use of this.
Note: this is a candidate for the stable branches.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit c73245882c)
Conflicts:
src/mesa/swrast/s_renderbuffer.c
_mesa_delete_renderbuffer() should free the mutex (though that may be a
no-op) and then free the renderbuffer object itself. Subclasses of
gl_renderbuffer can use this function too.
Reviewed-by: José Fonseca <jfonseca@vmware.com>
(cherry picked from commit 8472bb4508)
GLX uses mapi/glapi/libglapi.la, which is only built for OpenGL.
If the user specified --enable-xlib-glx --disable-opengl, error out, as these
cannot be both observed at the same time. If the user just specified
--disable-opengl but not --disable-glx, print a warning and disable GLX as
well.
NOTE: This is a candidate for the stable branches.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59364
Tested-by: Tom Stellard <thomas.stellard@amd.com>
(cherry picked from commit 3b888f534c)
The gallium docs for pipe_screen::is_format_supported() says that
samples==0 or samples==1 both mean that multisampling is not supported.
Return GL_MAX_SAMPLES==0 instead of 1 for consistency with other drivers.
Note: This is a candidate for the 9.0 branch.
Reviewed-by: Marek Olšák <maraeo@gmail.com>
(cherry picked from commit d60da27273)
The swrast fragment program interpreter has trouble computing the
right texture LOD because it doesn't have easy access to input
derivatives. This causes the GLSL-based meta generate mipmap code
to fetch texels from the wrong mipmap level.
One possible fix would be to set the GL_TEXTURE_MIN/MAX_LOD parameters
to limit sampling from the right level. But let's just use the
_mesa_generate_mipmap() fallback since it's a lot faster than using
the fragment shader interpreter.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=54240
Note: This is a candidate for the 9.0 branch.
Reviewed-by: José Fonseca <jfonseca@vmware.com>
(cherry picked from commit 89551ae04f)
See previous commit for more info.
Note: This is a candidate for the 9.0 branch.
Reviewed-by: José Fonseca <jfonseca@vmware.com>
(cherry picked from commit 2180f32972)
Only drivers supporting DRI2 version >=4 support GLX_INTEL_swap_event.
So lets mark it as such otherwise applications which use this extension
(i.e. everything based on Clutter, e.g. gnome-shell) break horribly on
drivers supporting DRI2 versions only up to 3.
Note: This is a candidate for the 9.0 branch.
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit dbb2d192de)
configure should warn if libxml2 is not found.
libxml2 is needed by glapi/gen.
Fixes error during build in src/mapi/glapi/gen:
ImportError: No module named libxml2
NOTE: This is a candidate for the 9.0 branch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31598
Reviewed-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 410b58c7bf)
The GLSL 1.40 spec says:
"Uniform block names and variable names declared within uniform
blocks are scoped at the program level."
Track the block name in the symbol table and emit errors when conflicts
exist.
Fixes es3conform's uniform_buffer_object_block_name_conflict test, and
fixes the piglit block-name-clashes-with-{variable,function,struct}.vert
tests.
NOTE: This is a candidate for the 9.0 branch.
v2: Fix bad constructor initialization. Noticed by Topi Pohjolainen.
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit 4f29169913)
Effectively this path would always assert. Move the break statement to
the (probable) intended place.
Note: This is a candidate for the stable branches.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
(cherry picked from commit 06f3a1f792)
Fixes piglit glx-dont-care-mask test.
Note: This is a candidate for the stable branches.
Reviewed-by: Chad Versace <chad.versace@linux.intel.com>
(cherry picked from commit fe90762414)
Fixes piglit glx-dont-care-mask test.
Note: This is a candidate for the stable branches.
Reviewed-by: Chad Versace <chad.versace@linux.intel.com>
(cherry picked from commit 46bad058eb)
If the call fails, we should return NULL from XMesaCreateVisual().
This was found when Waffle tried to create a visual with depth/stencil
bits = -1. That's an illegal value for glXChooseFBConfig() and we should
return NULL in that situation.
Note: This is a candidate for the stable branches.
(cherry picked from commit 05cd6cfd5f)
No piglit regressions and now passes glsl-uniform-out-of-bounds-2.
validate_uniform_parameters now checks that the array index is
valid. This means if an index is out of bounds, glGetUniform* now
fails with GL_INVALID_OPERATION, as it should.
_mesa_uniform and _mesa_uniform_matrix also call
validate_uniform_parameters so the bounds checks there became
redundant and were removed.
The test in glGetUniformLocation is modified to check array bounds
so it now returns GL_INVALID_INDEX (-1) if you ask for the location
of a non-existent array element, as it should.
Signed-off-by: Frank Henigman <fjhenigman@google.com>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
(cherry picked from commit 46e3aeb077)
Previously, Mesa code assumed that glReadBuffer(GL_NONE) was only
valid for user-created framebuffer objects. However, the spec is
quite clear that is should also be valid for the default framebuffer.
From section 18.2.1 ("Obtaining Pixels from the Framebuffer") of the
GL 4.3 spec:
"When READ_FRAMEBUFFER_BINDING is zero, i.e. the default
framebuffer, src must be one of the values listed in table 17.4,
including NONE."
Similar language exists in the GLES 3.0 spec, and in desktop GL all
the way back to ARB_framebuffer_object.
Partially fixes GLES3 conformance test "CoverageES30.test".
NOTE: This is a candidate for stable branches.
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit cf5632094b)
In exec_prepare() we were comparing pointers to see if the fragment
shader variant had changed before calling tgsi_exec_machine_bind_shader().
This didn't work reliably when there was a lot of shader token malloc/
freeing going on because the memory might get reused.
Instead, bind the shader variant during regular state validation.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=40404
(fixes a couple of piglit's glsl-max-varyings test)
Note: This is a candidate for the stable branches.
(cherry picked from commit 18ef8f83b2)
The old call to tgsi_exec_machine_bind_shader() in
softpipe_delete_fs_state() was never called since the shader's original
tokens are never passed to the tgsi interpreter (only shader _variant_
tokens are). Now, unbind the variant's tokens from the tgsi interpreter
when we free the variant.
This doesn't fix any known bugs but it's the right thing to do.
Note: This is a candidate for the stable branches.
(cherry picked from commit fddcc67f5c)
The GL 3.1 and ES 3.0 specs say of glGetActiveUniformsiv:
"If an error occurs, nothing will be written to params."
So, make a pass through the indices and check that they're valid before
the pass that actually writes to params. Checking pname happens on the
first iteration of the second loop.
Fixes es3conform's getactiveuniformsiv_for_nonexistent_uniform_indices
test.
NOTE: This is a candidate for the 9.0 branch.
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 11cea47246)
Otherwise the driver announces 4096 vertex shader constants and other
way too high limits.
NOTE: This is a candidate for stable release branches.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 654a945f4d)
Conflicts:
src/mesa/drivers/dri/r200/r200_context.c
NOTE: This is a candidate for stable release branches.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6a4e1bc1e)
Conflicts:
src/mesa/drivers/dri/radeon/radeon_context.c
Fixes flat shading for AA lines. demos/src/trivial/line-smooth is a
test case which hits this.
Note: This is a candidate for the stable branches.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit d2c7fe5389)
We need to clamp vertex buffer fetch based on its size, not based on the
user specified max index hint.
This matches draw_pt_fetch_run() above.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit 7da3a947c7)
The NV formulation of primitive restart is turned on/off with
glEnableClientState/glDisableClientState. These two functions don't
exist in core contexts, which mean that GL_NV_primitive_restart is
essentially useless...even broken.
However, leaving it on causes oglconform's primitive-restart-nv tests to
run in OpenGL 3.1 contexts, which results in them all failing. This
patch causes 29 subtests to go from "fail" to "not run".
NOTE: This is a candidate for stable branches.
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit 32c6db3978)
Only fail if GLX_SAMPLE_BUFFERS_ARB or GLX_SAMPLES_ARB are non-zero.
We were already doing this in the older swrast/glx code.
This fixes a piglit/waffle problem where we'd always fail to get a
visual/config and report the test as "skip".
Note: This is a candidate for the stable branches.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit c6d74bfaf6)
We need to rebase colors (ex: set G=B=0) when getting GL_LUMINANCE
textures in following cases:
1. If the luminance texture is actually stored as rgba
2. If getting a luminance texture, but returning rgba
3. If getting an rgba texture, but returning luminance
A similar fix was pushed by Brian Paul for uncompressed textures
in commit: f5d0ced.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=47220
Observed no regressions in piglit and ogles2conform due to this fix.
This patch will cause failures in intel oglconform pxconv-gettex,
pxstore-gettex and pxtrans-gettex test cases. The cause of failures
is a bug in test cases. Expected luminance value is calculted
incorrectly in test cases: L = R+G+B.
V2: Set G = 0 when getting a RG texture but returning luminance.
Note: This is a candidate for stable branches.
Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
(cherry picked from commit 9ab896243c)
Fixes part of es3conform's transform_feedback_init_defaults test.
NOTE: This is a candidate for the stable branch.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit 13f9012ad3)
v2: Perform this count the same way as elsewhere in this file, per
Brian Paul's review.
Fixes part of es3conform's transform_feedback_init_defaults test.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit 7c2060f0f0)
4bits and 3bits quantitization values differ significantly for
values other than 0 and 1.
Fixes piglit draw-pixels for softpipe/llvmpipe.
NOTE: Probably a candidate for stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Marek Olšák <maraeo@gmail.com>
(cherry picked from commit 0cb0c38cce)
v2: Fix mangled sentence in the comment, and make the loop exit early.
Fixes assertion failures in Piglit's spec/ARB_occlusion_query2/render
test as well as the game PlaneShift.
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com> (v1)
(cherry picked from commit e755c1a36b)
We are now seing cs that can go over the vram+gtt size to avoid
failing flush early cs that goes over 70% (gtt+vram) usage. 70%
is use to allow some fragmentation.
The idea is to compute a gross estimate of memory requirement of
each draw call. After each draw call, memory will be precisely
accounted. So the uncertainty is only on the current draw call.
In practice this gave very good estimate (+/- 10% of the target
memory limit).
v2: Remove left over from testing version, remove useless NULL
checking. Improve commit message.
v3: Add comment to code on memory accounting precision
This version is a backport for mesa 9.0
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Marek Olšák <maraeo@gmail.com>
The bug: The printed horizontal stride was the numerical value of the
BRW_HORIZONTAL_$N enum.
The fix: Translate the enum before printing.
Note: This is a candidate for the stable releases.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chad Versace <chad.versace@linux.intel.com>
(cherry picked from commit ca7d332253)
The sampler appears to ignore writemasks (even when correcting the
WRITEMASK_XYZW in brw_vec4_emit.cpp to the proper writemask) and just
always writes all four values.
To cope with this, just texture into a temporary, then MOV out into a
register that has the proper number of components.
NOTE: This is a candidate for stable branches.
Fixes es3conform's shadow_execution_vert.test.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
(cherry picked from commit f0dbd9255b)
Previously it was left undefined, causing us to select a random LOD.
NOTE: This is a candidate for stable branches.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
(cherry picked from commit aeff9a0d98)
This is purely a refactor. However, in a moment, we'll want to set
lod_type to float for ir_tex, where ir->lod_info.lod is NULL.
NOTE: This is a candidate for stable branches (for the next patch).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
(cherry picked from commit 56ce55d198)
This is needed to compute render_to_fbo. It even has the comment.
NOTE: This is a candidate for stable branches.
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit bd87441ac0)
Fixes oglconform shad-compiler advanced.TestLessThani.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48629
NOTE: This is a candidate for the 9.0 branch.
Acked-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 0482998ccc)
Conflicts: fs_inst doesn't have a "predicate" field on the 9.0 branch,
so convert it to "predicated = true". See 54679fcbca.
The maximum number of URB entries come from the 3DSTATE_URB_VS and
3DSTATE_URB_GS state packet documentation; the thread count information
comes from the 3DSTATE_VS and 3DSTATE_PS state packet documentation.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
(cherry picked from commit 9add4e8038)
We weren't lowering textureGrad() with samplerCubeShadow because I
couldn't figure out the LOD calculations. It turns out they're easy:
you just have to use 1 for the depth. This causes it to pass
oglconform's four tests.
(cherry picked from commit 613e64060c)
When cherry-picking this to stable, I've reordered this before the
Haswell commit that would have introduced a regression.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Tested-by: Anuj Phogat <anuj.phogat@gmail.com> (original)
Tested-by: Ian Romanick <idr@freedesktop.org> (original)
Haswell supports EXT_texture_swizzle and legacy DEPTH_TEXTURE_MODE
swizzling by setting SURFACE_STATE entries. This means we don't have to
bake the swizzle settings into the shader code by emitting MOV
instructions, and thus don't have to recompile shaders whenever the
swizzles change.
Unfortunately, we can't handle GL_ALPHA this way: unlike all the others,
which store the comparison result in the .r channel (and possibly others
as well), GL_ALPHA puts it in the .a channel. The GLSL 1.30+ style
functions which return a float always simply return the .r channel,
which would be zero if we handled this as a surface override. In this
case, fall back to doing it the old way. DEPTH_TEXTURE_MODE = GL_ALPHA
isn't an interesting performance path anyway.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 6d6aef7974)
It's going to be reused in a second place soon.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit b5a042a657)
Haswell moved the "Cut Index Enable" bit from the INDEX_BUFFER packet to
a new 3DSTATE_VF packet, so we need to emit that. Also, it requires us
to specify the cut index rather than assuming it's 0xffffffff.
This adds a new Haswell-specific tracked state atom to gen7_atoms.
Normally, we would create a new generation-specific atom list, but since
there's only one difference over Ivybridge so far, I chose to simply
make it return without doing any work on non-Haswell systems.
Fixes five piglit tests:
- general/primitive-restart-DISABLE_VBO
- general/primitive-restart-VBO_COMBINED_VERTEX_AND_INDEX
- general/primitive-restart-VBO_INDEX_ONLY
- general/primitive-restart-VBO_SEPARATE_VERTEX_AND_INDEX
- general/primitive-restart-VBO_VERTEX_ONLY
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
(cherry picked from commit 815d9d405c)
Otherwise, we crash when the callback is executed, since the dri2_surf
pointer may point to invalid data.
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
LOOP_START_DX10 ignores the LOOP_CONFIG* registers, so it is not limited
to 4096 iterations like the other LOOP_* instructions. Compute shaders
need to use this instruction, and since we aren't optimizing loops with
the LOOP_CONFIG* registers for pixel and vertex shaders, it seems like
we should just use it for everything.
Reviewed-by: Marek Olšák <maraeo@gmail.com>
(cherry picked from commit 810345492e)
Fixes a hang on the following piglit test on my rv770
./bin/ext_timer_query-time-elapsed -auto -fbo
Tom Stellard:
-Keep --with-libclc-path and mark it deprecated.
Reviewed-by: Tom Stellard <thomas.stellard@amd.com>
(cherry picked from commit 959e83d650)
Also remove the recently added and overloaded LLVM_CXXFLAGS from CXXFLAGS.
Note: This is a candidate for the stable branches.
Reviewed-by: Tom Stellard <thomas.stellard@amd.com>
(cherry picked from commit 21694b8eac)
Conflicts:
src/gallium/auxiliary/Makefile
command mistakenly used vector instead of scalar emit (the more or less
identical code in radeon is already correct).
Seems like it would be broken ever since kms probably.
Should fix bugs 22576, 26809.
(cherry picked from commit 320d531373)
I erroneously added this back in January 2011 in commit 88421589.
Looking at the commit message, I have no idea why I added it. It only
added non-array structure fields to the symbol table, so array structure
fields are treated correctly.
Fixes piglit tests structure-and-field-have-same-name.vert and
structure-and-field-have-same-name-nested.vert. It should also fix
WebGL conformance tests shader-with-non-reserved-words.
NOTE: This is a candidate for the stable release branches.
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57622
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit ed3f237e09)
Coverity pointed out this uninitialised class member.
Note: This is a candidate for stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit f3476ec8fa)
coverity pointed out this field was being used uninitialised.
Note: This is a candidate for stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 906670a790)
To fix a pipe_context::surface_destroy() use-after-free problem.
We previously added pipe_sampler_view_release() for similar reasons.
Note: this is a candidate for the stable branches.
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 51223784d6)
Until we have proper 'make dist' this is an improvement of the current
situation, because each time some old Makefiles got converted to automake
we had to update the tarballs target.
NOTE: This is a candidate for the 9.0 branch.
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Matt Turner <mattst88@gmail.com>
(cherry picked from commit 0f5e2ce854)
Conflicts:
Makefile.am
Commit 774fb90db3 introduced a ralloc context to
each user of struct brw_compile, but for this one a NULL context was used,
causing the later ralloc_free(mem_ctx) to not do anything.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55175
NOTE: This is a candidate for the stable branches.
(cherry picked from commit 59bfd66a61)
The bug was found by Coverity.
NOTE: This is a candidate for the stable branches.
Signed-off-by: Vinson Lee <vlee@freedesktop.org>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit 10f214e5b2)
For GLES1 and GLES2, brwCreateContext neglected to validate the requested
context version received from the DRI layer. If DRI requested an OpenGL
ES2 context with version 3.9, we provided it one.
Before this fix, the switch statement that validated the requested GL
context flavor was an ugly #ifdef copy-paste mess. Instead of reproducing
the copy-past-mess for GLES1 and GLES2, I first refactored it. Now the
switch statement is readable.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chad Versace <chad.versace@linux.intel.com>
(cherry picked from commit 243cf7a924)
It seems that -NDEBUG and other flags might still be leaked through
those variables, so strip those off there as well.
NOTE: This is a candidate for the 9.0 branch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
(cherry picked from commit ddb901fbf4)
The diff looks funny, but it's moving the integer vs non-integer check
below the _mesa_source_buffer_exists() check that ensures
_ColorReadBuffer is non-null, so we get a GL_INVALID_OPERATION instead
of a segfault. This looks like it had regressed in the
_mesa_error_check_format_and_type() changes, which removed the first of
the two duplicated checks for the source buffer. Fixes segfault in the
new piglit ARB_framebuffer_object/negative-readpixels-no-rb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45877
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit 5c99697f74)
MaxLog2 led to bugs, because it didn't work well with 1D and 3D textures.
NOTE: This is a candidate for the stable branches.
v2: correct the comment at MaxNumlevels
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 8111342e81)
We were accidentally setting bit 14 in DWord 2 (which is Reserved/MBZ)
rather than bit 14 in DWord 3 (which is AA Line Distance Mode).
There's also no reason to ever set it to legacy mode; the bit is only
used when drawing antialiased lines anyway. Set it unconditionally.
NOTE: This is a candidate for stable branches.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit e639385064)
Previously we were accepting garbage after #else and #endif tokens when
the previous preprocessor conditional evaluated to false (eg, #if 0).
When the preprocessor hits a false conditional, it switches the lexer
into the SKIP state, in which it ignores non-control tokens. The parser
pops the SKIP state off the stack when it reaches the associated #elif,
#else, or #endif. Unfortunately, that meant that it only left the SKIP
state after the lexing the entire line containing the #token and thus
would accept garbage after the #token.
To fix this we use a mid-rule, which is executed immediately after the
#token is parsed.
NOTE: This is a candidate for the stable branch
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56442
Fixes: preprocess17_frag.test from oglconform
Reviewed-by: Carl Worth <cworth@cworth.org> (glcpp-parse.y)
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 060e696799)
The GL_POINT_BIT state attribute GL_POINT_SPRITE_COORD_ORIGIN
is only supported on OpenGL-2.0 or later. Prevent glPopAttrib()
from trying to restore it on OpenGL-1.4 implementations which
support GL_ARB_POINT_SPRITE, as otherwise the sequence...
glPushAttrib(GL_POINT_BIT);
glPopAttrib();
throws an GL_INVALID_ENUM error in glPopAttrib().
See also commit f778174ea1
NOTE: This is a candidate for the 9.0 branch.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit eabbe5c45f)
Since cf438f5375e242, we store actual integers for the attribute data.
We just need to reinterpret the GLfloat array as a GLint/GLuint array
so we can read the proper data.
Fixes oglconform's glsl-vertex-attrib/basic.VertexAttribI[1234][u]i
subtests (after fixing an unrelated bug in those test cases).
v2: Use the COPY_4V macro to be concise.
NOTE: This is a candidate for the stable branches.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Marek Olšák <maraeo@gmail.com> [v1]
(cherry picked from commit c299f44782)
I've no idea why there isn't a piglit that triggers this behaviour,
but while enabling TBOs for softpipe and r600g, I noticed all the
integer tests failed. I tracked it back to the TXF returning a float
when it should be returning an int. This fixed it and I haven't
seen any regressions in a full piglit run on softpipe.
http://bugs.freedesktop.org/55010
NOTE: This is a candidate for the 9.0 branch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 9785ae0973)
Integer textures generate invalid operation in glGenerateMipmap.
So, the code related to integer textures is now redundant.
Note: This is a candidate for stable branches.
Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit a196f43596)
Khronos has reached a conclusion and disallowed following texture formats in
glGenerateMipMap():
(a) ASTC textures
(b) integer internal formats (e.g., RGBA8UI, RG16I)
(c) textures with stencil formats (e.g., STENCIL_INDEX8)
(d) textures with packed depth/stencil formats (e.g, DEPTH24_STENCIL8)
https://cvs.khronos.org/bugzilla/show_bug.cgi?id=9471
Note: This is a candidate for stable branches.
Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit c0a78d7d7b)
This is part of fixing gl-3.1/genned-names.
v2: Fix a missing return value.
NOTE: This is a candidate for the 9.0 branch.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
(cherry picked from commit 947d8ff4a7)
Tested with a modified glean tstencil2 test.
NOTE: This is a candidate for stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit f69fc36127)
This fixes an issue where glsl_to_tgsi_visior::get_opcode() would emit the
wrong opcode because the register type was GLSL_TYPE_ARRAY/STRUCT instead of
GLSL_TYPE_FLOAT/INT/UINT/BOOL, so the function would use the float opcodes for
operations on integer or boolean values dereferenced from an array or
structure. Assertions have been added to get_opcode() to prevent this bug
from reappearing in the future.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Tested-by: Andreas Boll <andreas.boll.dev@gmail.com>
(cherry picked from commit 170f0459a2)
Consider the following code, which reinterprets a register as a
different type:
mov(8) g6<1>F g1.4<0,4,1>.xF
and(8) g5<1>.xUD g6<4,4,1>.xUD 0x7fffffffUD
Copy propagation would notice that we can replace the use of g6 with
g1.4 and eliminate the MOV. Unfortunately, it failed to preserve the UD
type, incorrectly generating:
and(8) g5<1>.xUD g6<4,4,1>.xF 0x7fffffffUD
Found while debugging Ian's uncommitted ARB_vertex_program LOG opcode
test with my new Mesa IR -> Vec4 IR translator.
NOTE: This is a candidate for stable release branches.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 03ea156f1b)
Consider the following code sequence:
mul(8) g4<1>F g1<0,4,1>.wzwwF g3<4,4,1>.wzwwF
mov.sat(8) m1<1>.xyF g4<4,4,1>F
mul(8) g4<1>F g1<0,4,1>.xxyxF g3<4,4,1>.xxyxF
mov.sat(8) m1<1>.zwF g4<4,4,1>F
The compute-to-MRF pass will discover the first mov.sat and attempt to
replace it by rewriting earlier instructions. Everything works out,
so it replaces scan_inst's destination file, reg, and reg_offset,
resulting in:
mul(8) m1<1>F g1<0,4,1>.wzwwF g3<4,4,1>.wzwwF
mul(8) g4<1>F g1<0,4,1>.xxyxF g3<4,4,1>.xxyxF
mov.sat(8) m1<1>.zwF g4<4,4,1>F
Unfortunately, it loses the .xy writemask on the mov.sat's MRF
destination. While this doesn't pose an immediate problem, it then
proceeds to transform the second mov.sat, resulting in:
mul(8) m1<1>F g1<0,4,1>.wzwwF g3<4,4,1>.wzwwF
mul(8) m1<1>F g1<0,4,1>.xxyxF g3<4,4,1>.xxyxF
Instead of writing both halves of the vector (like the original code),
it overwrites the full vector both times, clobbering the desired .xy
values.
When encountering a MOV, the compute-to-MRF code scans for instructions
which generate channels of the MOV source. It ensures that all
necessary channels are available (possibly written by several
instructions). In this case, *more* channels are available than
necessary, so we want to take the subset that's actually used.
Taking the bitwise and of both writemasks should accomplish that.
This was discovered by analyzing an ARB_vertex_program test
(glean/vertProg1/MUL test (with swizzle and masking)) with my new
Mesa IR -> Vec4 IR translator code. However, it should be possible
with GLSL programs as well.
NOTE: This is a candidate for stable release branches.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 10ff6772c8)
Previously, we used lookahead patterns to differentiate:
#define FOO(x) function macro
#define FOO (x) object macro
Unfortunately, our rule for function macros:
{HASH}define{HSPACE}+/{IDENTIFIER}"("
relies on infinite lookahead, and apparently triggers a Flex bug where
the generated code overflows a state buffer (see YY_STATE_BUF_SIZE).
There's no need to use infinite lookahead. We can simply change state,
match the identifier, and use a single character lookahead for the '('.
This apparently makes Flex not generate the giant state array, which
avoids the buffer overflow, and should be more efficient anyway.
Fixes piglit test 17000-consecutive-chars-identifier.frag.
NOTE: This is a candidate for every release branch ever.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Carl Worth <cworth@cworth.org>
(cherry picked from commit 9142ade154)
We should use the later since we're freeing the memory with free(),
not the gallium FREE() macro.
This fixes a mismatch when using the gallium debug memory functions.
NOTE: This is a candidate for the 9.0 branch.
(cherry picked from commit bb93439873)
MaxIfDepth of 0 means "flatten all the time", not "never flatten".
This is only desirable on hardware that can't support control flow;
software rasterization and most hardware drivers want this.
This alters behavior for swrast as well as i915. Tested on i915.
NOTE: This is a candidate for stable release branches.
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
(cherry picked from commit 56705cd36b)
commit a010215463 removed ES2 specific dispatch
table and remap_helper, since now we are using dispatch.h which is generated
from gl_and_es_API.xml we need to generate a matching remap_helper using the
same xml.
Note: This is a candidate for the 9.0 branch.
Signed-off-by: Tapani Pälli <tapani.palli@intel.com>
Reviewed-by: Chad Versace <chad.versace@linux.intel.com>
(cherry picked from commit 60565b564b)
Only the first 'nr_cbufs' color buffers in the pipe_framebuffer_state are
valid. The rest of the color buffer pointers might be unitialized.
Fixes a regression in the piglit fbo-srgb-blit test since changes in the
gallium blitter code.
NOTE: This is a candidate for the 9.0 branch (just to be safe).
Reviewed-by: Jose Fonseca <jfonseca@vmware.com>
(cherry picked from commit 60a9390978)
To validate this code, I ran piglit -t vs quick.tests with the "go spill
everything" debugging code enabled. There was only one regression:
glsl-vs-unroll-explosion simply ran out of registers. This should be
fine in the real world, since no one actually spills every single
register.
NOTE: This is a candidate for the 9.0 branch. Even if it proves to have
bugs, it's likely better than simply failing to compile.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 9237f0ea8d)
move_grf_array_access_to_scratch() calculates scratch buffer offsets in
bytes. However, emit_scratch_read/write() expects the base_offset
parameter to be measured in OWords.
As a result, a shader using a scratch read/write offset greater than
zero (in practice, a shader containing more than one variable in
scratch) would use too large an offset, frequently exceeding the
available scratch space.
This patch corrects the mismatch by removing spurious conversion from
OWords to bytes in move_grf_array_access_to_scratch().
This is based on a patch by Paul Berry.
NOTE: This is a candidate for stable release branches.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit 46e529672b)
Since wl_display_dispatch_queue() returns the number of processed events
or -1 on error, only cancel the roundtrip if an -1 is returned.
This also fixes a potential memory corruption bug happening when the
roundtrip does an early return and the callback later writes to the then
out of scope stack allocated `done' parameter.
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
When a client frame callback is executed and the client starts rendering
again, the egl event queue might not have been dispatched so that the
buffer release event for the previous frame hasn't been processed. In
that case a third buffer is allocated, even though it would be possible
to reuse the buffer that was just released.
The wl_display_dispatch_queue_pending() entry point is available from
wayland-client 1.0.2, so require that in configure.ac. Also, just
let the pkg-config macro throw its own error, which will show what version
we were looking for and failed to find.
Note: This is a candidate for stable branches.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Commit ca3ed3e024 fixed the problem where
eglMakeCurrent would trigger a getbuffer callback that then breaks the
following wl_egl_window_resize() call. However, we still need to
invalidate buffers in eglSwapBuffers, since in wayland we always swap
buffers, so the dri driver needs to come out and ask us for the next buffer
after each swapbuffer.
Note: this is a candidate for stable branches.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
We used to invalidate the drawable after a call to eglSwapBuffers(),
so that a wl_egl_window_resize() would take effect for the next frame.
However, that leads to calling dri2_get_buffers() when eglMakeCurrent()
is called with the current context and surface, and a later call to
wl_egl_window_resize() would not take effect until the next buffer
swap.
Instead, add a callback from wl_egl_window_resize() back to the wayland
egl platform, and invalidate the drawable only when it is resized.
This solves a bug on wayland clients when going back to windowed mode
from fullscreen when clicking a pop up menu, where the window size
after this would be the fullscreen size.
Note: this is a candidate for stable branches.
CC: wayland-devel@lists.freedesktop.org
i.e. we have to allocate a temporary tiled resource if dst isn't tiled.
This fixes hardlocks on r6xx-r7xx, though using a linear resource is forbidden
on later asics as well.
NOTE: This is a candidate for the stable branches.
(cherry picked from commit 9c6410e5c3)
Conflicts:
src/gallium/drivers/r600/r600_blit.c
src/gallium/drivers/r600/r600_texture.c
The burst was incorrectly used, because ELEM_SIZE was always 0.
I don't know if the burst works, because I don't know of any test
which uses it.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 6a2ec765bd)
Conflicts:
src/gallium/drivers/r600/r600_shader.c
While developing cube map array support I found that we didn't
support this properly, also piglit didn't test for it at all.
I've submitted a test to piglit to check for this, and this
fixes explicit lod and lod bias with cube maps.
NOTE: This is a candidate for the 9.0 branch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 037b4f8038)
This fixes graphics corruption in the case where the DISCARD_RANGE flag
is used to map a buffer.
NOTE: This is a candidate for the stable branches.
(cherry picked from commit cff4c948ed)
Array textures were broken.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit e7dde5c8fb)
Array textures were broken.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 6dd839f23a)
It was pretty broken with array textures, where the array size (height or
depth depending on the target) shouldn't be magnified.
The guessing also doesn't fail with 1D and cube textures.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit c06258dd02)
Conflicts:
src/mesa/state_tracker/st_cb_texture.c
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 985f2aec4a)
Conflicts:
src/mesa/main/texstorage.c
MaxLog2 led to bugs, because it didn't work well with 1D and 3D textures.
NOTE: This is a candidate for the stable branches.
v2: correct the comment at MaxNumlevels
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 8111342e81)
Conflicts:
src/mesa/main/teximage.h
The functions were broken, because they converted ints to floats.
Now we can finally advertise OpenGL 3.0. ;)
In this commit, the vbo module also tracks the type for each attrib
in addition to the size. It can be one of FLOAT, INT, UNSIGNED_INT.
The little ugliness is the vertex attribs are declared as floats even though
there may be integer values. The code just copies integer values into them
without any conversion.
This implementation passes the glVertexAttribI piglit test which I am going
to commit in piglit soon. The test covers vertex arrays, immediate mode and
display lists.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
v2: cosmetic changes as suggested by Brian
(cherry picked from commit acf438f537)
This is a regression since b3921e1f53.
The array stores VS outputs, not FS inputs.
Now llvmpipe can do 32 varyings too.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
(cherry picked from commit 183e122bdf)
And the clear color too, though that may be an issue only with GL_RGB if it's
actually RGBA in the driver.
NOTE: This is a candidate for the stable branches.
Reviewed-by: Brian Paul <brianp@vmware.com>
v2: The types of st_translate_color parameters were changed to gl_color_union
and pipe_color_union as per Brian's comment.
(cherry picked from commit 2bbd307fa6)
For precise lts support I had to do some magic with the library names, which works fine
as long as the libraries from pkg-config are used.
The parts with src/gallium/targets/va-*/Makefile will not apply on the master branch,
but do apply to the 9.0 branch.
NOTE: This is a candidate for the 9.0 branch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Matt Turner <mattst88@gmail.com>
(cherry picked from commit 4f0537e645)
<li><ahref="https://bugs.freedesktop.org/show_bug.cgi?id=55175">Bug 55175</a> - Memoryleak with glPopAttrib only on Intel GM45</li>
<li><ahref="https://bugs.freedesktop.org/show_bug.cgi?id=56442">Bug 56442</a> - glcpp accepts junk after #else/#elif/#endif tokens</li>
<li><ahref="https://bugs.freedesktop.org/show_bug.cgi?id=56706">Bug 56706</a> - EGL sets error to EGL_SUCCESS when DRI driver fails to create context</li>
<li><ahref="https://bugs.freedesktop.org/show_bug.cgi?id=57746">Bug 57746</a> - build test failure: nouveau_fbo.c:198:3: error: too few arguments to function 'nouveau_renderbuffer_del'</li>
<li><ahref="https://bugs.freedesktop.org/show_bug.cgi?id=57754">Bug 57754</a> - [swrast] Mesa 9.1-devel implementation error: Unable to delete renderbuffer, no context</li>
<li><ahref="https://bugs.freedesktop.org/show_bug.cgi?id=58680">Bug 58680</a> - [IVB] Graphical glitches in 0 A.D</li>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
